AT A GLANCE
Strong enough for the road, sized for the job.
Mobile tanks see vibration, surge, and weather. Ours are compartmented against surge, gusseted where the design requires it, and welded from solid sheet with no molded weak points.
- MATERIAL
- Copolymer polypropylene (PP) or high-density polyethylene (HDPE) sheet, chosen by the fluid and your specification
- EXTERIOR WALLS
- 1/2″ or 3/4″ per the design. Internal partitions are sized to the design
- SIZE
- Built to your footprint and capacity, to the 1/8″; from small reservoirs to 3,000-gallon tanks
- STRUCTURE
- Interlocking partitions every bay, support gussets where the size requires them
- PORTS
- NPT-tapped lid ports, 1/4″ to 6″; drain port, sight tube, and bulkhead fittings optional
- MOUNTING
- Skid base, forklift pockets, mounting tabs, or pads with brass inserts, per your drawing
- FLUIDS
- Water, wash and process water, and chemical solutions; compatibility confirmed against resin data for your fluid and temperature
- CONSTRUCTION
- Extrusion welded inside and out to DVS 2205 / 2207 practice
- TESTING
- Hydrostatic and spark tested before shipment
- LEAD TIME
- Averages under 6 weeks after approved drawings
- WARRANTY
- 3-year limited warranty (SPEC_0100)
STANDARD ON EVERY TANK
- PP or HDPE sheet; 1/2″ or 3/4″ exterior walls per design
- Partitioned, with support gussets where the size requires
- Lid with NPT ports located to your drawing
- Lifting pegs with 2″ galvanized eye bolts
- Extrusion welded inside and out to DVS standards
- Tank ID, capacity, date of manufacture, and Made in USA on every tank
- 3-year limited warranty
OPTIONS & ACCESSORIES
Options for the way the tank is used.
Pick what the application needs. Everything is placed on the submittal drawing before fabrication.
- 1Custom NPT threaded ports, 1/4″ to 6″Lid or side ports sized and located to your plumbing.
- 2NPT threaded drain port with plugLow-point drain for washdown and winterizing.
- 3Sight tube(s)Clear 1/2″ tube with elbows inside an enclosed poly guard.
- 4Forklift pockets, skid base, or mounting tabsFor moving the tank and bolting it to a truck bed, trailer, or skid.
- 5Mounting pads with brass insertsWelded pads with threaded inserts for brackets, pumps, and hose reels.
- 6Stainless D-rings or lifting barIn place of eye bolts, for crane or hoist handling.
- 7Internal polypropylene or stainless pipingSuction and fill lines run inside the tank.
- 8Textured materialTextured sheet finish in place of smooth.
- 9Multiple compartmentsSeparate fluids in one welded tank, each with its own fill and drain.
WHERE THEY GO TO WORK
Trucks, trailers, skids, and shops.
Truck- and trailer-mounted tanks
Water supply, washdown, and pest control spray tanks built to the bed, the trailer, and the GVWR the builder is working with.
Skid-mounted process tanks
Process water and chemical solution tanks sized to the skid, with ports and mounting tabs where the frame and pump sit.
Open water holding tanks
Custom open-top tanks for live fish holding, wash-down, and water storage, welded with smooth interior walls and the drains and overflows you specify.
Spill containment trays
Secondary containment trays, basins, and sumps for drums, totes, and equipment, sized to the footprint and the volume you need to hold.
QUESTIONS WE GET
What equipment builders ask first.
Will polypropylene or HDPE hold my chemical?
Usually. Tell us the fluid, the concentration, and the service temperature and we will confirm compatibility.
Can it mount on a truck?
Yes. Skid bases, forklift pockets, mounting tabs, and pads with brass inserts are welded to the tank where your drawing calls for them, and the floor is supported per the installation guide.
How big can you go?
At Collab Plastic Designs we specialize in tanks 3,000 gallons and below.
What do you need for a quote?
The footprint, the capacity, the fluid, and how the tank mounts. A drawing is welcome but not required; we draft one for the quote.
DOCUMENTS
For your submittal package.
Need something specific for a purchasing or quality file? Email us and we will provide what is required.
GETTING STARTED
Send us a specification or a drawing.
That is all it takes to start. You get a quote with a rendering of your tank, then a submittal drawing with every port placed and every dimension finalized before we cut sheet.
You send a spec or a drawing
A formal drawing, a sketch, or just the footprint, capacity, and fluid. Port sizes, mounting, and quantity help if you have them.
We return a quote with a rendering
Your tank drawn to your dimensions, so you can see the fit before you commit.
You approve a submittal drawing
Ports placed, features selected, dimensions finalized. Production starts on your approval.
NO MOLDS · NO MINIMUM ORDERS · A REAL PERSON ON THE PHONE